Product ID:XYRON 241
MSDS Date:03/31/1993
FSC:3439
NIIN:00N090119
Status Code:A
MSDS Number: CHXYS

EUTECTIC CORPORATION

1515 BROOK DR
DOWNERS GOVE, IL 60515
US

Emergency Phone: 800-232-4845

Info Phone: 800-232-4845

Cage: EO060

EUTECTIC CORPORATION

DOWNERS GROVE, IL 60515 US

Telephone: 800-323-4845

Cage: EO060

NICKEL (SARA 313) (CERCLA)

CAS: 7440-02-0

RTECS: QR5950000

Fraction By Weight: >50%

OSHA PEL 1 MG/M3

ACGIH TLV: 1 MG/M3; 9495

BARIUM CARBONATE

CAS: 513-77-9

RTECS: CQ8600000

Fraction By Weight: 5-10%

OSHA PEL 5 MG BA/M3

ACGIH TLV: 2 MG BA/M3

CALCIUM FLUORIDE (AS F)

CAS: 7789-75-5

RTECS: EW1760000

OSHA PEL 2.5 AS F (MFR)

ACGIH TLV: 2.5 AS F (MFR)

COPPER (SARA 313) (CERCLA)

CAS: 7440-50-8

RTECS: GL5325000

Fraction By Weight: 1-5%

OSHA PEL 0.1MG/M3 FUME/1 DUST

ACGIH TLV: 0.2 MG/M3 FUME; 9495

EPA Report Quantity: 5000 LBS

DOT Report Quantity: 5000 LBS

GRAPHITE, NATURAL

CAS: 7782-42-5

RTECS: MD9659600

OSHA PEL 15 MPPCF; Z-3

ACGIH TLV: 2 MG/M3 RDUST; 9495

NIOBIUM (ALSO CALLED COLUMBIUM); (COLUMBIUM/NIOBIUM)

CAS: 7440-03-1

OSHA PEL N/K

ACGIH TLV: N/K

TIN

CAS: 7440-31-5

RTECS: XP7320000

OSHA PEL 2 MG/M3

ACGIH TLV: 2 MG/M3; 9495

IRON

CAS: 7439-89-6

RTECS: NO4565500

OSHA PEL 10 TOTAL PART (MFR)

ACGIH TLV: 5 TOTAL PART (MFR)

WELDED, PROCESS, PROCS, & ELECTRODES/OTHER

RTECS: 9999999ZZ

COMPLEX OXIDES OF METAL OXIDES, CARBON &

RTECS: 9999999ZZ

NITROGEN OXIDES, & CERTAIN INERT GASES USED AS

RTECS: 9999999ZZ

FUMES & GASES TO WHICH WORKERS ARE EXPOSED IS TO

RTECS: 9999999ZZ

THE WELDER'S BREATHING ZONE. FOR MORE SPECIFIC

RTECS: 9999999ZZ

2B. NTP 7TH ANNUAL RPT ON CARCIN, 1994

RTECS: 9999999ZZ

LIGHT CAN INJURE EYES & BURN SKIN. LIQS

RTECS: 9999999ZZ

BURNS HANDLED W/CARE AS SHOWN IN SECTION 7. WEAR

RTECS: 9999999ZZ

& FACE SHIELD FOR ALL FLUXES & CHEM AIDS. ELEC

RTECS: 9999999ZZ

SWALLOWED. PRIMARY ROUTE OF ENTRY OF WELDING FUMES,

RTECS: 9999999ZZ

MAY ALSO OCCUR W/POWDERS, PASTES & LIQ. ACGIH REC

RTECS: 9999999ZZ

OTHERWISE CLASSIFIED, IS 5 MG/M3 & 10 MG/M3

RTECS: 9999999ZZ

USED AS GUIDES IN CNTRL OF HLTH HAZ & SHOULD NOT BE

RTECS: 9999999ZZ

MOST WELDING, EVEN W/PRIMITIVE VENT, DOES NOT

RTECS: 9999999ZZ

WHICH DOES, SHOULD BE CONTROLLED." FOR MORE

RTECS: 9999999ZZ

CALL A PHYSICIAN AND/OR LOCAL

RTECS: 9999999ZZ

AREA. TRAIN WELDER TO KEEP HIS/HER FACE AWAY FROM THE

RTECS: 9999999ZZ

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:YES IARC:YES OSHA:NO
Health Hazards Acute and Chronic:LITTLE/NO HAZ EXIST FOR ARC WELDING
ELECTRODES & BRAZING RODS BEFORE THEY ARE USED IN WELDING PROCESS.
WARNING! POTNTL HLTH EFTS OF PROD LISTED, & WHEN USED IN
ASSOCIATION W/WELDING, BRAZING, SOLDERIN G, THERMAL SPRAYING/PART
PREPARATION ARE LISTED BELOW. SEE ALSO SECTION 5 FOR HAZ DECOMP
PRODS. (EFTS OF OVEREXP)
Explanation of Carcinogenicity:NICKEL: IARC MONO ON THE EVALUATION OF
CARCIN RISK OF CHEMS TO MAN, VOL 49, PG 257, 1990: GROUP 2B. (ING
14)
Effects of Overexposure:HLTH HAZ: INHAL: FUMES ASSOCD W/HEATING,
WELDING, BRAZING, SOLDERING/CUTTING METALS CAN BE DANGEROUS TO YOUR
HLTH & OVEREXP CAN CAUSE LUNG DMG &/OTHER ORGAN DMG. USE ADEQ VENT
TO KEE BELOW EXPOS LIMIT S. KEEP FUMES & GASES FROM BRTHG ZONE.
KEEP WELDER'S HEAD OUT OF FUMES. EYE/SKIN CNTCT: ARC RAYS &
ULTRAVIOLET (ING 15)
Medical Cond Aggravated by Exposure:AGGRAVATION OF PREEXISTING
RESPIRATORY OR ALLERGIC CONDITIONS MAY OCCUR IN SOME WORKERS.

First Aid:INHAL OVEREXP: MOVE VICTIM TO FRESH AIR SOURCE. CNTCT A MD &
ADVISE ON INGREDS LISTED IN SECTION 2. SKIN CNTCT: THOROUGHLY WASH
HANDS/EFFECTED AREAS W/SOAP & H*2O TO REMOVE ALL RESIDUE. IF
RASH/BURN D EVELOPS, CONSULT A MD. EYE CNTCT: THOROUGHLY FLUSH EYE
W/H*2O FOR AT LEAST 15 MIN TO REMOVE ALL RESIDUE. OBTAIN PROMPT MED
ADVICE FOR FLUXES & CHEM AIDS. ADVISE MD OF INGS LISTED IN SECTION
2 (ING 24)

Extinguishing Media:CO*2, DRY CHEMICAL FOAM TYPE.
Fire Fighting Procedures:USE NIOSH APPROVED SCBA & FULL PROTECTIVE
EQUIPMENT . TOXIC FUMES MAY BE PRODUCED.
Unusual Fire/Explosion Hazard:SOME FLUXES & CHEM AIDS MAY GIVE OFF
HYDROGEN CHLORIDE, PHOSGENE & CHLORINE GASES. CANS, UNDER PRESS, &
FLAMMS MAY EXPLODE. REFER TO ANSI Z49.1 FOR (SUPAT)

Spill Release Procedures:USE APPROPRIATE MEASURES TO KEEP AIRBORNE DUST
LEVELS CONTAINED IN ACCORDANCE WITH EXPOSURE LEVELS OF SECTION 2.
SEE ALSO SECTION 7 FOR PROPER SAFE HANDLING AND STORAGE.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling and Storage Precautions:PLEASE READ AND UNDERSTAND THE PRODUCT
LABEL INFORMATION FOR PROPER PROCEDURES AND USE.
Other Precautions:SEE ANSI Z49.1 'SAFETY IN WELDING AND CUTTING,' AND
CHAPTER 11 OF 'THERMAL SPRAYING,' PUBLISHED BY THE AMERICAN WELDING
SOCIETY AND OSHA PUBLICATION 2206 (29 CFR 1910) FOR MORE DETAIL.

Respiratory Protection:IF THE WORK STATION IS NOT PROPERLY VENTILATED
TO EXHAUST ALL FUMES, VAPORS AND DUSTS BELOW THE RECOMMENDED
EXPOSURE LIMITS, USE A NIOSH APPROVED RESPIRATOR.
Ventilation:USE ENOUGH GENERAL VENT & LOC EXHST AT WORK SITE TO KEEP
ALL FUMES & DUST FROM WORKER'S BRTHG ZONE & GENERAL (ING 25)
Protective Gloves:IMPERVIOUS GLOVES .
Eye Protection:ANSI APPROVED CHEM WORKERS GOGGS(SUPDAT)
Other Protective Equipment:ANSI APPRVD EMER EYE WASH & DELUGE SHOWER .
FOR MORE SPECIFIC INFORMATION CONTACT NEHC .
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
EXPLO HAZ: FIRE PVNT DURING USE OF WELDING & ALLIED PROCESSES.
ELECTRODE/BRAZE/SOLDERS: GENERALLY NONFLAM, WELDING ARC, SPARKS &
FLAMES CAN IGNITE COMBUST & FLAMMS. FOR MORE SPECIFIC INFO CNTCT
NEHC ( ). HAZ DECOMP PROD: CANNOT BE CLASSIFIED SIMPLY.
COMPOSITION & QTY OF THESE ARE DEPENDENT UPON METAL BEING (ING 9)

Appearance and Odor:NONE SPECIFIED BY MANUFACTURER.

Stability Indicator/Materials to Avoid:NO
NONE SPECIFIED BY MANUFACTURER.
Stability Condition to Avoid:NONE SPECIFIED BY MANUFACTURER.
Hazardous Decomposition Products:FUMES, GASES & DUSTS GIVEN OFF DURING
HEATING, WELDING, BRAZING, SOLDERING, CUTTING/THERMAL SPRAY
PROCESSES (SUPDAT)

Waste Disposal Methods:DISPOSE OF WASTE MATERIAL, POWDERS, GRINDING, OR
FILTER RESIDUES IN AN ENVIRONMENTALLY SENSITIVE MANNER IN
ACCORDANCE WITH FEDERAL, STATE AND LOCAL REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.